FREE SHIPPING to 45 states on orders over $149!

Aggreseal Supreme Acrylic Aggregate Sealer

No reviews yet Write a Review
$7.00 - $242.06

Description

Aggreseal Concrete Sealer

SOLVENT BASED PREMIUM ACRYLIC CONCRETE SEALER


Aggreseal Supreme is Surfkoat's famous acrylic sealer specially designed and produced for exposed aggregate concrete. Aggreseal offers deep color enhancement and a rich Wet Look with a high-gloss finish. Aggreseal is also a great choice for many other applications where a premium acrylic is desired. Aggreseal is available in a clear or brown tinted formula to complement and enhance all types of decorative concrete, exposed aggregate and/or pea gravel concrete.

Aggreseal's easy application, durability and UV-stable non-yellowing formula make it the industry standard for acrylic aggregate sealers. Aggreseal Supreme is our #1 best-selling aggregate sealer, and the choice of all our professional contractors.

 

Aggreseal is a great choice for all types of concrete!

Exposed Aggregate
Exposed Aggregate Sealer
Tinted Sealer
Tinted Sealer Stain
Stamped Concrete
Sealer for Stamped Concrete
Stained Concrete
Sealer for Stained Concrete
 

Not sure which product is right for you?
We Offer Sample Sizes of All Our Most Popular Products.. Including Aggreseal!

 

Essentials

  • For all types of Concrete
  • Clear or Brown Tinted
  • Solvent Based
  • Wet Look
  • High-Gloss Finish
  • 30% Solids Acrylic (700 VOC)
  • 25% Solids Acrylic (350 VOC)
  • Brush / Roller Application
  • 100 sq. ft. / gallon (aggregate)

 

Std. VOC Tech Data Sheet

Std. VOC Safety Data Sheet (Clear)

Std. VOC Safety Data Sheet (Brown Tinted)

 

Low VOC Tech Data Sheet

Low VOC Safety Data Sheet (Clear)

Low VOC Safety Data Sheet (Brown Tinted)

 

WARNING!!!!! Be sure to select the proper VOC version for your area!

Standard VOC version CANNOT be shipped to California*, Colorado, Connecticut, Delaware, District of Columbia, Illinois, Indiana, Maine, Maricopa County of Arizona, Maryland, Massachusetts, New Hampshire, New Jersey, New York, Northern VA*, Ohio, Pennsylvania, Rhode Island or Northwest Utah*.

All other states EXCEPT California*, Colorado, Connecticut, Delaware, Maryland, New York, Rhode Island, Maricopa County of Arizona, and Northwest Utah* may purchase either version.

NO version of this product can be shipped to California*, Colorado, Connecticut, Delaware, Maryland, New York, Rhode Island, Maricopa County of Arizona or Northwest Utah*. If you are in these areas please do not try to order this product. We WILL NOT be able to process your order!!!

* See VOC MAP for specific regulated areas.

 


Detailed Info!

To learn more, keep reading or click a link below to jump to a specific topic:

 


Aggreseal Supreme

Exposed aggregate, pea gravel concrete, pebble concrete, exposed chip or whatever it is called in your area... needs to be sealed and protected more than any other type of concrete! There are lots of options based on your needs and desires, but day in and day out Aggreseal Supreme is almost always the choice of our professional contractors!

Aggreseal is available in both a clear and brown tinted formula. The brown tint is subtle and transparent, not over-powering. The tint is designed to darken and enhance the natural colors of brown pea gravel.

Aggreseal is also available in both "standard VOC" and "low VOC" to accommodate laws in a majority of states. Like most "low VOC" solvent-based products, the "low VOC" version of Aggreseal dries faster than the standard version. For this reason, the "low VOC" version is produced in a slightly lower, 25% solids formula. We recommend special care be taken to avoid application of this version in hot temperatures or direct sunlight. The "low VOC" version is great in situations where a fast-drying product is needed, no matter what your local regs are. If you are in a low VOC area, we encourage you to carefully explore all of the options available to you.

Aggreseal, along with most solvent-based acrylics, is compatible with many other similar solvent-based acrylics that may already exist on previously sealed concrete. Solvent-based acrylics should never be applied over any existing water-based sealer. If your concrete has an existing water-based sealer, it must be removed before applying Aggreseal.

Aggreseal can be used clear, with color or with our special matting agent. Each part of the system is sold separately to maximize versatility.

 

Color Tint For Acrylic SealersAcrylPack Color:

Color can easily be added to clear Aggreseal to create beautiful, semi-transparent or solid colors. AcrylPack Color is available in 14 great colors to fit any situation. Colors can also be mixed to create endless combinations. Simply add less pigment to achieve a more translucent color or use up to 8oz / gallon for a solid opaque color.

 

Transparent Tint For Acrylic SealersAggreseal Tint:

Aggreseal Tint Packs are also available and make it easy for you to tint your own Clear Aggreseal or any of our other solvent-based acrylics if needed. These tint packs are the same transparent brown and gray tint used in the pre-tinted pails of Aggreseal. You may also use these to add additional tint if a darker color is desired. Follow directions on Aggreseal Tint Packs for mixing instructions. For most consistent results, add color to both coats.

 

Matting Additive for Acrylic SealersMatte-50:

If a lower gloss, matte or satin finish is desired, Matte-50 Matting Additive can also be added to easily create the exact gloss level you desire. Simply add less Matte-50 to achieve a higher gloss finish or use up to 8oz / gallon for a beautiful matte finish. Add Matte-50 to second coat only.

 

No Slip Additive for Acrylic SealersSurface Grip

If additional texture is needed, Surface Grip may be used for additional slip resistance. Adding Surface Grip is a great way to reduce slip and falls, reduce gloss/reflection and also hide minor imperfections in the concrete.

 

Cleaning and Preparation Instructions

1. Completely remove all oils and contaminates from the surface. All previous sealers or coatings must be removed before application unless they are a compatible solvent-based acrylic. Use only cleaning methods suitable for the substrate you are cleaning. Clean oily concrete with Concrete Degreaser. Use a bristle brush for heavily oiled spots. Area to be treated must be clean, porous and sound.

2. Use only the amount of cleaners necessary to remove contaminates, oils, fluids and sealers from the substrate. If using acidic cleaners to etch surface or to remove efflorescence, calcium, rust, etc, be sure to neutralize and restore pH with Balance Neutralizer. Rinse thoroughly! Surface and pores must be clean, dry and free of all chemicals before applying Aggreseal.

3. If using over cured trowel finished concrete, diamond grinding is always recommended to open the surface and allow adhesion of the sealer. Do not grind finer than 100 grit. Beyond 100 grit, sealer adhesion will be compromised. Dry grinding is highly recommended to avoid introduction of moisture into the concrete. If diamond grinding is not possible, first etch with Surf-Prep.

4. Allow area to dry completely.

 

Application Instructions

Always test in an inconspicuous area before use to ensure compatibility and desired results!

For best results apply by roller. Use a long nap roller for exposed aggregate, a medium nap roller for textured surfaces and a short nap roller for smooth surfaces. A brush may be used to apply to edges and expansion joints where a roller can't reach. Do not allow to Puddle! Thick or puddled areas may prevent the solvent from evaporating and may be susceptible to moisture intrusion which may cause milky white spots. Applying too thin may cause sealer to prematurely delaminate, flake or wear away. Allow sealer to dry for 24 hours for light traffic and at least 48 hours for heavy traffic. If applying two coats, wait approximately 4-6 hours between coats. Do not thin product.

Make sure all sprinklers are turned off for a 24 hour period of time. Apply Aggreseal only if rain is not expected for at least 24 hours. Do not apply Aggreseal if surface temperature is below 40° F., or above 80° F. If possible always apply as concrete is cooling, rather than as concrete is warming. Warming by the sun causes the air inside the concrete to expand and push out through the surface, often causing bubbles in the still wet sealer.

MATTE FINISH ADDITIVE: If a low gloss, matte or satin finish is desired, Matte-50 Matting Additive can be added  to create the exact gloss level you desire. Follow directions on Matte-50 for mixing instructions. Add Matte-50 to second coat only.

COLOR ADDITIVE: If a tinted or colored sealer is desired, AcrylPack Color Tint or Aggreseal Color Tint can be added to create beautiful transparent or solid colors. Follow directions on tint pack for mixing instructions. For most consistent results, add color to both coats.

SLIP RESISTANCE: Surface Grip may be used for additional slip resistance or added texture. Adding Surface Grip is a great way to reduce slip and falls, reduce gloss/reflection and also hide minor imperfections in the concrete. Follow mixing instructions and do not overload system. When using a non-skid additive in acrylics, do not add to first coat. Add it to second coat. The addition of an anti-skid additive will make spraying difficult, so roll-on application is typically recommended when using Surface Grip. All non-skid additives may shorten the life of the film to some degree.

CLEAN UP: Clean up tools with A1 Solvent or Xylene.

 

Of course, having the right tools will make your job easier, so scroll to the bottom to see our recommended Sprayers, Rollers and Application Tools!

 

Coverage Rates

Coverage rates are approximate and will vary depending on substrate density, porosity, temperature, application method and desired appearance. In most cases, two coats are recommended. Total project estimate includes both coats, and is on average how much total product you should apply to each type of surface. Coverage rates are based on bare, clean, dry, un-sealed surfaces. On previously sealed concrete, coverage rates WILL vary.

Note: In some cases, on exposed aggregate, it may be acceptable to apply the entire "total project volume" in one heavy coat. This will depend on temperature, substrate porosity and ESPECIALLY skill level and experience of the applicator.

Exposed Aggregate: 100-125 sq. ft. / gallon (total project estimate)
1st coat - 175-225 sq. ft / gallon
2nd coat - 225-275 sq. ft / gallon

Broom Swept Concrete: 125-150 sq. ft. / gallon (total project estimate)
1st coat - 225-275 sq. ft / gallon
2nd coat - 275-325 sq. ft / gallon

Stamped Concrete: 150-175 sq. ft. / gallon (total project estimate)
1st coat - 275-325 sq. ft / gallon
2nd coat - 325-375 sq. ft / gallon

Trowelled Concrete: 150-200 sq. ft. / gallon (total project estimate) 
1st coat - 250-350 sq. ft / gallon
2nd coat - 350-450 sq. ft / gallon

 

Maintenance

Like all things, maintaining optimal protection of a sealed surface requires scheduled maintenance. Once properly applied, surfaces sealed with Aggreseal Supreme may periodically require a light cleaning to remove dirt, dust, mud, etc. In most cases, low pressure water is all that is needed for routine cleaning. Do not use a hot-water pressure washer unless you are preparing to apply a maintenance coat of Aggreseal Supreme. Re-seal surface every two years or as needed to prevent buildup of sealer.

 

FAQ's

 

Shipping Restrictions Warning

Standard VOC version CANNOT be shipped to California*, Colorado, Connecticut, Delaware, District of Columbia, Illinois, Indiana, Maine, Maricopa County of Arizona, Maryland, Massachusetts, New Hampshire, New Jersey, New York, Northern VA*, Ohio, Pennsylvania, Rhode Island or Northwest Utah*.

All other states EXCEPT California*, Colorado, Connecticut, Delaware, Maricopa County of Arizona, Maryland, New York, Rhode Island and Northwest Utah* may purchase either version.

NO version of this product can be shipped to California*, Colorado, Connecticut, Delaware, Maricopa County of Arizona, Maryland, New York, Rhode Island and Northwest Utah*. If you are in these areas please do not try to order this product. We WILL NOT be able to process your order!!!

* See VOC MAP for specific regulated areas.

Got Questions?

Check out the "Help Center", send us an email or just give us a call and we'll be glad to help you with your order!

Extra Information

Brand:
Surfkoat
"Wet Look" Color Enhancement?:
Yes
VOC Compliance:
LADCO (IL,IN,OH)
VOC Compliance:
OTC-Phase-1 (DC,MA,ME,NH,NJ,PA,VA)
VOC Compliance:
CARB-2002

Additional Resources

Shop by Brand

Bakers
Surfkoat
F9
Diamabrush
Chapin
Swissmex
Polyrez
Malish
TeeJet
F9
Homax
Spraying Systems Co
Coval